Accessory Units
Digital
| Product | Description | Applications | Documents  |
|
| Digital Input/output Module |
 |
Expansion of inputs and outputs for HEINZMANN control units and PLC |
|
|
| Analogue Input/output Module |
 |
Expansion of inputs for HEINZMANN control units and PLCs |
|
Leaflet I/O Module |
Analogue
| Product | Description | Applications | Documents |
|
| AT 01 |
 |
Analogue Generator Management AT 01 The AT 01 unit includes a synchroniser, a load sharer, a load ramp and an integrated soft loading. |
|
Leaflet THESEUS analogue Manual THESEUS AT 01 |
| AT 10-01 |
 |
Analogue Generator Management AT 10-01 The AT 10-01 is a costeffective unit for singl ephase application. It includes a synchroniser, a load sharer and a load ramp. |
|
Leaflet AT 10-01 |
| SyG 02 |
 |
Analogue Synchrocoupleur unit SYG02 The SyG 02 synchroniser has threephase voltage detection with frequency and phase control over a paralleled generator. The unit has direct control of the generator speed and will pull a generator into synchronism from within +/- 2 Hz of synchronous frequency. |
|
Manual SyG 02 |
| LMG IF-02 |
 |
Load share inteface unit LMG-IF-02 The Load Share Interface Unit LMG-IF-02 is used to couple load share lines of differing systems which work at different voltage levels. |
|
Manual LMG IF 02 |
| LR 01 |
 |
Ramp Generator unit LR-01 Accessories for LMG10-01 which gives possibility to ramp up or down the load of generators connected with grid. |
|
|
| LSchG 02 |
 |
2 Chanel Load Switch unit LSchG-02 Accessories for load sensor: needs a load-sensitive control signal of 0-5V. |
|
|
| LKG 02 |  |
Load Import/Export controller LKG 02 Accessories for LMG 10-01 LKG02 makes a regulation for load import / export. |
|
|
| GSLU 01 |  |
Ramp Generator GSLU 01 Accessories for LMG 10-01 the GSLU 01 unit allows parallel engines to isochronously load ramp in mains parallel and island applications. |
|
|
| SPAG 03 |  |
Voltage Matching Unit SPAG 03 The voltage matching unit will match the voltages between the generator and a BUS. The output is a raise / lower signal which will interface to the AVR motor potentiometer. |
|
|
| PFC 01 |  |
Cosinus Phi Regler PFC-01 The power factor controller allows the control of reactive load via a motor potentiometer connected to the generator AVR. |
|
|
| BSBG 01 |  |
Analogue Speed rampe BSBG 01 Makes analogue speed ramp adjust. |
|
|
| SFBG 03 |  |
Analogue Start fuel limiter or Load limiter Additional functionality for control units in the range of KG 6 to KG 40. |
|
|
| SA 02 | Load Anticipation unit SA 02 This unit when detecting load inpact (positive or negative) will immediately adjust the speed in order to avoid a speed drop. |
|
||
| PG 01 |
 |
Analogue engine simulator | ||
Setpoint adjusters
| Product | Description | Applications | Documents |
|
| SW 01-1-o |
One turn setting potentiometer | |||
| SW 01-1-b |
One turn setting potentiometer | |||
| SW 02-10-o |
Ten turn setting potentiometer | |||
| SW 02-10-b |
Ten turn setting potentiometer | |||
| ESW 01 |
 |
Electronics Setting Potentiometer ESW01 To be used with with HEINZMANN governing systems in the range from E1/2-F up to E40 and E2000. ESW01 is converting digital speed Increase/Decrease to an analogue. |
Manual ESW 01 |
|
| SW 03-1-M-15 sec |
 |
Motorpotentiometer SW-03-1-M-15 sec
|
Manual Motor Potentiometer |
|
| SW 04-10-M-150 sec | Motorpotentiometer SW-04-10-M-150 sec
|
Manual Motor Potentiometer | ||
| SW 07-1-M-120 sec |  |
Motorpotentiometer SW-07-1-M-120
|
Manual Motor Potentiometer | |
| SW 09-URI |  |
Setting converter Convert current or voltge signal into an analogue speed setting signal |
||
| EFP |  |
Elektronics Foot pedale Electronics signal which convert a position into a speed setting signal. |
||
| SW 05-P | Pneumatic Setpoint Unit SW 05-P
|
|||
Power supplies
| Product | Description | Applications | Documents |
|
| NG 01-2 + NSV 01-2 |  |
Three phases Power supply NG 01-2 + NSV 01-2 + back up unit for analogue or digital HEINZMANN Governing system from E1/E2-F up to E40. Batterie in conformity with Marine application. |
Manual NG 01 | |
| NG 04 + NSV 03 |
One phase Power supply NG 04 + NSV 03 + back up unit for analogue or digital HEINZMANN Governing system from E1/E2-F up to E40. Batterie in conformity with Marine application. |
Manual NG 04 |
||
| NG 08 + NSV 05 |
Three phases Power supply NG 08 + NSV 05 + back up unit for analogue or digital HEINZMANN Governing system from E64 up to E180. Batterie in conformity with Marine application. |
Manual NG 08 |
||
| NG 09 |
Three phases Power supply NG 09 without back up unit for analogue or digital HEINZMANN Governing system from E64 up to E180. |
Manual NG 09 | ||
| NG 10 |
One phase Power supply NG 10 for analogue or digital HEINZMANN Governing system from E6 up to E40. |
Manual NG 10 |
||
